微波EDA (www.mweda.com) 网友回复：

• 网友回复

  我单位的机子都装不上，不知道怎么回事，也许和破解有关系吧，要不就是机子的问题，不支持

• 网友回复

  我用beta好像问题好大阿,可能是破解问题吧,也有可能是beta本身的错误吧

• 网友回复

  是啊，但我同事的老机子是装上的拉，可能是我机子的问题吧

• 网友回复

  都出11了，我10还刚用上呢，不过10比9的确有所改进，不知道11改进了什么

• 网友回复

  Version 11.0 Major Enhancements
  
  ===============================
  
  Solving:
  
  - Higher-order basis functions incorporated for improved accuracy and solution efficiency
  
  - Improved port-solver to handle lower frequencies, and decrease noise floor
  
  - Analytic ports for rectangular, circular, and coaxial port geometries to improve modal
  
    consistency and port accuracy
  
  - Iterative solver option reduces RAM requirements for large solutions and makes use of
  
    multiple processors to handle more than one excitation
  
  
  
  
  
  Meshing:
  
  - Higher-quality tetrahedra with lower aspect-ratio to promote faster convergence
  
  
  
  
  
  Floquet Ports:
  
  - Produce higher accuracy at large scan angles
  
  - Provide additional information that is particularly useful for periodic structures, such
  
    as phased-array antennas and frequency-selective surfaces: separation of fields into
  
    modes, phase information available for each mode
  
  
  
  
  
  Screening Impedance Boundary:
  
  - Available to replace geometrically complex periodic screens or grids
  
  - Isotropic or anisotropic impedance can be specified directly or through a link to another
  
    unit-cell design
  
    
  
  Incident Fields:
  
  - Total-field formulation now uses E- and H-field information from the incident wave
  
  - Incident field from small current loop is now available
  
  
  
  
  
  Design Link:
  
  - SIWave-HFSS and HFSS-HFSS links based on E- and H-fields
  
  - Additional option to update source field pattern at each adaptive pass
  
  
  
  
  
  Distributed Solve Option:
  
  - Automatic distribution of individual discrete and interpolating sweep frequencies to different
  
    nodes
  
  - Distributed solve available for all Optimetrics' setups, including Optimization, Sensitivity,
  
    and Statistical Analysis
  
  
  
  
  
  Optimetrics:
  
  - Addition of Genetic Algorithm
  
  - Latin Hypercube Sampling now included in statistical analysis setup
  
  
  
  
  
  Desktop:
  
  - Toolbar customization
  
  
  
  
  
  Modeler:
  
  - Upgrade to ACIS R16 SP6
  
  - Auto-assignment of terminals at port setup eliminates need for terminal lines
  
  - New commands: Region, Thicken Sheet, Sweep Face Along Normal
  
  - Enhanced manual-healing GUI and more advanced auto-healing procedure during geometry import
  
  - CATIA v4 and v5 geometry import now available
  
  - GDSII export now available
  
  
  
  
  
  Post-Processing:
  
  - Fully scriptable new report editor and 2D plot GUI
  
  - Copy and paste of data from one report to another
  
  - Generation of report templates
  
  - Ranged functions to extract calculations such as maximum, minimum and average from a plot
  
    or dataset
  
  - Mesh statistics available in the solution data panel
  
  - Antenna parameters: front-to-back ratio as part of antenna parameters; 3-dB beamwidth and
  
    sidelobe levels included as part of the ranged functions

• 网友回复

  另外有一点，我想说的是：
  不要动不动就把问题规到Crack上。其实，要校验Crack是否有问题，很简单，真正又有多少人做过？
  现在的软件、资料都来得太容易，人们很容易浮躁，我们需要做的是Design，而不是拿个软件随便跑跑。要用好这些软件，首先得有基本功。

• 网友回复

  大家要把HFSS-VCRedist-vcredist_x86.exe先运行一下，这样才能装的上
  还有就是无论路径还是文件名还有里面的名称也不要出现中文，
  我的机器装上就挺好用的，我同事他们就有的用不起来

• 网友回复

  1.我昨天装了一下,当时我的也报错了,发现是FLEXID装不上,后来发现是和我的杀毒软件有冲突,关闭杀毒软件后(当然你首先要确定你的HFSS内不含毒,用杀毒软件扫一下)重装了一遍后通过。
  2.然后，把HFSSFIX.COM拷贝到你的---：“某盘：\Ansoft\HFSS10” 文件下下，双击‘HFSSFIX.COM”。
  3.把license.lic拷贝到你的---：“某盘：\Ansoft\admin”文件夹下即可！

• 网友回复

  网上公认v11的破解有问题,我现在用的时候发现计算结果有,但是在结果处理的时候老提示无结果,晕,头大,算得快是很快.

• 网友回复

  我用HFss11 beta 好像还好吗。只是有些小问题。

• 网友回复

  我今天刚装上,感觉不错
  就是暗装之前先运行一下HFSS>>VCRedist-vcredist_x86.exe后再安装就 没问题了
  不然就会报错,说什么应用程序出错
  

• 网友回复

  我用9和10都不停的报错说硬盘空间不够
  自从用了v11，跑麻麻顺，从来不错

• 网友回复

  11占的内存和硬盘空间都小了...
  速度有些提高..

申明：网友回复良莠不齐，仅供参考。如需专业解答，推荐学习李明洋老师的HFSS培训视频，或咨询本站专家。