Thermal Loss Distribution Overview

Thermal loss distributions are computed from electromagnetic fields or particle losses and link the thermal solver to other CST STUDIO SUITE solvers. In principal a thermal computation can be don within the electromagnetic- / particle-project or in a separate project.

The thermal loss distribution is always mapped to the grid of thermal solver and is added to the 2D / 3D Results tree folder during the simulation process.

 

Single project coupling

If both the electromagnetic field solver and the thermal solver are based on a hexahedral grid, it is possible to carry out both computations within a single project. This type of coupling allows to do parameter sweep and optimizations of a coupled thermal simulation.

The workflow to link in the thermal solver is as follows:

  1. Define electromagnetic field monitors (for some solvers not necessary).

  2. Calculate electromagnetic fields or particle distributions.

  3. Import losses into thermal solver (Solve Thermal Loss Distribution).

  4. Run the thermal simulation (Solve Thermal Stationary Solver / Thermal Transient Solver).

The thermal loss distribution is calculated automatically right before the thermal solver starts.

 

Two projects coupling

If the meshes of the primary solver an the thermal solver should be different, two different projects need to be connected. The workflow is as follows:

  1. Define electromagnetic field monitors (for some solvers not necessary).

  2. Calculate electromagnetic fields or particle distributions.

  3. Calculate thermal loss distributions (Results Calculate Thermal Losses).

  4. Switch to the thermal project.

  5. Import losses into thermal solver (Solve Thermal Loss Distribution).

  6. Run the thermal simulation (Solve Thermal Stationary Solver / Thermal Transient Solver).

This workflow requires to compute the thermal loss distributions manually or via postprocessing template after the electromagnetic- or particle-simulation has been finished.

 

Creating simulation tasks

Another possibility to perform parameter sweep and optimizations of a coupled thermal simulation is to create multiple simulation project simulation tasks in DESIGN STUDIO and couple them in the way described in the previous section.

  1. Switch to the DESIGN STUDIO tab of the project.

  2. Create the needed sequence of simulation projects (Simulation New Simulation Project...).

  3. Couple the simulation projects as it has been described in the previous section.

For more information please refer to CST DESIGN STUDIO help.

 

Field Monitors

Some electromagnetic solvers require to define field monitors in order to store the electromagnetic fields for a subsequent thermal loss calculation. The following table gives an overview which monitors deliver usable results:

 

Field monitor

Description

Electric field

Electric fields are used together with the material properties to compute volumetric thermal loss distributions. Only available for hexahedral-based solvers.

Current density field

Current density fields are used together with the material properties to compute volumetric thermal loss distributions. Only available for hexahedral-based solvers.

Magnetic field

Magnetic fields can be used to compute surface based thermal losses caused by surface impedance models or volumetric thermal losses caused inside dispersive materials. Only available for hexahedral-based solvers.

Power loss density

Power loss densities only need to be mapped to the grid which is used by the thermal solver. This is the only available type of monitor for tetrahedral based solvers.

Particle losses

Particle losses are not recorded by usage of a monitor definition, but with a special solver option in the Tracking- or PIC-solver settings.

 

Note: Power loss densities are created by an interpolation from field results. Since the discrete representation of these losses is not located where the thermal solver needs it, a second interpolation is necessary. To avoid inaccuracies it is always advisable to use electric or current density monitors for the thermal loss distribution calculation instead of power loss densities if possible. Tetrahedral solvers only support the linkage with power loss densities to the thermal solver.

 

Loss Interpolation

 

Transferring losses from EM- or Particle solvers to thermal solvers involves at least one interpolation step. In addition the loss distribution is a secondary result in any EM- / Particle-solver which means that an electric field, a magnetic field or a particle movement is evaluated to create the loss distribution. Summing up the following sequence of steps is performed to create a loss distribution which can be used by a thermal solver:

 

  1. Compute EM fields

  2. Evaluate loss distribution

  3. Extract losses for the sub-volume of the thermal simulation (incl. boundary settings)

  4. Interpolate losses to the thermal solvers mesh.

 

Especially during the steps 3 and 4 the total amount of loss power can be reduced compared to the value after step 2 was finished. There a various reasons why this happens and often this is intended by the user. The following factors can reduce the total amount of loss power:

 

 

It is very important for an accurate thermal simulation that the total amount of losses is transferred to the thermal solver correctly. Please check these values in the "Heat Flow Values" after the simulation was finished.

 

See also:

Thermal Stationary Solver Overview, Thermal Transient Solver Overview, Calculate Thermal Losses, Thermal Loss Distribution, Field Monitor