Designer仿真出错提示问题
12-09
请问是什么地方设置不对,提示我自我交叉...
该怎么改呢?
The edge port is not represented in the mesh : port3
couple5001000a (D:/Ansoft/)
PlanarEM1
[warning] Polygon poly_261 appears to be self-intersecting, this may result in an incorrect mesh. (5:41 下午 十一月 10, 2005)
[warning] Polygon poly_264 appears to be self-intersecting, this may result in an incorrect mesh. (5:41 下午 十一月 10, 2005)
[warning] Polygon poly_324 appears to be self-intersecting, this may result in an incorrect mesh. (5:41 下午 十一月 10, 2005)
[warning] Polygon poly_336 appears to be self-intersecting, this may result in an incorrect mesh. (5:41 下午 十一月 10, 2005)
[info] Number of triangles: 98 Number of rectangles: 0 (5:41 下午 十一月 10, 2005)
[info] Average minimum triangle angle: 31.7 Minimum triangle angle: 18.4 (5:41 下午 十一月 10, 2005)
[info] Number of edges: 198 Number of internal edges: 96 (5:41 下午 十一月 10, 2005)
[info] Average edge length: 0.00245 Maximum edge length: 0.00584 Maximum/Average: 2.4 (5:41 下午 十一月 10, 2005)
[info] Number of non-planar (3D) elements: 0 (5:41 下午 十
该怎么改呢?
The edge port is not represented in the mesh : port3
couple5001000a (D:/Ansoft/)
PlanarEM1
[warning] Polygon poly_261 appears to be self-intersecting, this may result in an incorrect mesh. (5:41 下午 十一月 10, 2005)
[warning] Polygon poly_264 appears to be self-intersecting, this may result in an incorrect mesh. (5:41 下午 十一月 10, 2005)
[warning] Polygon poly_324 appears to be self-intersecting, this may result in an incorrect mesh. (5:41 下午 十一月 10, 2005)
[warning] Polygon poly_336 appears to be self-intersecting, this may result in an incorrect mesh. (5:41 下午 十一月 10, 2005)
[info] Number of triangles: 98 Number of rectangles: 0 (5:41 下午 十一月 10, 2005)
[info] Average minimum triangle angle: 31.7 Minimum triangle angle: 18.4 (5:41 下午 十一月 10, 2005)
[info] Number of edges: 198 Number of internal edges: 96 (5:41 下午 十一月 10, 2005)
[info] Average edge length: 0.00245 Maximum edge length: 0.00584 Maximum/Average: 2.4 (5:41 下午 十一月 10, 2005)
[info] Number of non-planar (3D) elements: 0 (5:41 下午 十
是建模交叉了吧
看字面,我也是这么理解的.
模型是从cad里面转过来的,
双层四端口的耦合器.
但是如果取消两个端口,让他们悬空,虽然还是要提示,
但是能进行仿真
今天重新转一次试试
相关文章:
- 电磁场仿真优化软件包--IE3D(05-08)
- 电磁场仿真软件包&--FIDELITY(05-08)
- 请大侠推荐一个FDTD仿真方面的软件????(05-08)
- 请问目前主要有哪些FDTD的仿真计算软件?(05-08)
- 请问:有没有基于物理光学法的天线仿真软件?(05-08)
- 如果想仿真贴片天线上的电流分布,用什么软件?(05-08)
射频专业培训教程推荐