联合仿真lna 出现如下问题
05-08
[upload=1] [upload=1] Simulation / Synthesis Messages
Warning detected by hpeesofsim during TRAN analysis `SP1'.
COMPONENT `X4_LNA_schematic_13_1':
Simulator uses frequency lower than frequency range of Momentum model. The S-parameters are extrapolated.
Warning detected by hpeesofsim during TRAN analysis `SP1'.
COMPONENT `X4_LNA_schematic_13_1':
The model for the Layout Component is not found in the ModelDatabase, a new model is generated for the requested parameter values.
Warning detected by hpeesofsim during TRAN analysis `SP1'.
COMPONENT `X4_LNA_schematic_13_1':
The model for the Layout Component is reused from the ModelDatabase.
Warning detected by hpeesofsim during SP analysis `SP1'.
The simulation temperature (25.0 C) is not the same as the IEEE standard
noise temperature (290 K or 16.85 C) in the noise analysis `SP1'.
If the simulation temperature is not equal to the IEEE standard temperature,
then the loss and the noise figure will not agree for a passive circuit.
The `Temp' parameter on the Options item can be set to 16.85 C to
eliminate this warning message.
仿真几个小时之后给出这个提示,仿真结果S21为负值,噪声到70多最小噪声也是70多,请教是什么地方错误造成的,非常感谢。
Warning detected by hpeesofsim during TRAN analysis `SP1'.
COMPONENT `X4_LNA_schematic_13_1':
Simulator uses frequency lower than frequency range of Momentum model. The S-parameters are extrapolated.
Warning detected by hpeesofsim during TRAN analysis `SP1'.
COMPONENT `X4_LNA_schematic_13_1':
The model for the Layout Component is not found in the ModelDatabase, a new model is generated for the requested parameter values.
Warning detected by hpeesofsim during TRAN analysis `SP1'.
COMPONENT `X4_LNA_schematic_13_1':
The model for the Layout Component is reused from the ModelDatabase.
Warning detected by hpeesofsim during SP analysis `SP1'.
The simulation temperature (25.0 C) is not the same as the IEEE standard
noise temperature (290 K or 16.85 C) in the noise analysis `SP1'.
If the simulation temperature is not equal to the IEEE standard temperature,
then the loss and the noise figure will not agree for a passive circuit.
The `Temp' parameter on the Options item can be set to 16.85 C to
eliminate this warning message.
仿真几个小时之后给出这个提示,仿真结果S21为负值,噪声到70多最小噪声也是70多,请教是什么地方错误造成的,非常感谢。
你确定线都连好了?
我最近仿真也总是出现 这个The model for the Layout Component is not found in the ModelDatabase, a new model is generated for the requested parameter values不知道什么原因啊,坐等高手解答
我也出现问样问题了,望解答
相关文章:
- 请教ADS与HFSS联合仿真介质振荡器的问题。 (05-08)
- 关于ADS原理图和layout联合仿真问题求助(momentum) (05-08)
- ADS模拟数字加MATLAB联合仿真 (05-08)
- 怎么关联Matlab和C++呀?ADS中Matlab联合仿真要求的 (05-08)
- 求救:联合仿真那里出错了? (05-08)
- 用momentum联合仿真中的直流问题 (05-08)
射频专业培训教程推荐